SHIMANO Wheels WH-RX180 700C F12x100/R12x142mm HG walnut Center-Lock black

View the product manual.

Safety Notice
WARNING
Information on installation, adjustment and replacement of products that is not found in the user manual will be provided to you at the place of purchase or distributor. The dealer's manual intended for professional and experienced bicycle mechanics can be found on our website (https://si.shimano.com).
For safety, please read this "User Manual" thoroughly before use, follow it for correct use, and save it for future reference.
The following instructions must always be followed to prevent personal injury and physical damage to the equipment and surroundings. The instructions are classified according to the degree of danger or damage that may occur if the product is used incorrectly.
DANGER - Failure to follow the instructions will result in death or serious injury.
WARNING - Failure to follow the instructions could result in death or serious injury.
CAUTION - Failure to follow the instructions could result in personal injury or physical damage to the equipment and surroundings.

WARNING
- Do not disassemble or modify the product. This may cause the product to malfunction, you may fall unexpectedly and be seriously injured.
- Before riding the bicycle, check that the wheels are securely fastened. Improper use of the axle release lever may cause the wheel to come off, etc. and may lead to serious injury due to a fall or collision.
- Use the appropriate air pressure marked on the tire and rim. If the tires or rims have a maximum pressure listed, do not exceed the maximum pressure with the lower value. Higher than the specified pressure may cause sudden puncture and/or sudden loosening of the tire and cause serious injury.
WH-R9270-TL / WH-R8170-TL / WH-RS710-TL: maximum pressure = 7.5 bar / 109 psi / 750 kPa
WH-R9170-TL / WH-RS770-TL: maximum pressure = 8 bar / 116 psi / 800 kPa
WH-RS370-TL: maximum pressure = 6.5 bar / 94 psi / 650 kPa
WH-RX880-TL / WH-RX870-TL / WH-RX570-TL: maximum pressure = 5 bar / 72 psi / 500 kPa
- Before riding the bicycle, check the wheels to make sure that the spokes are not bent or loose and that there are no marks on the rim surface. nicks, scratches or cracks. If you find any of these problems, do not use the wheel. The wheel may break and you may fall. Check for any peeling or cracking of the carbon.
- Do not use the road wheel assembly on unpaved surfaces. The road wheel assembly is designed for paved surfaces. If the wheels are used on unpaved surfaces, they may bend or be damaged, which may result in an accident.
- Do not use the GRAVEL wheel assembly in rough conditions, such as on uneven roads. Do not use it for downhill cycling or freeriding, otherwise the wheel may bend or be damaged if subjected to a strong impact, which may result in an accident.
- Do not use with rim brakes. These wheels are designed for use with disc brakes only. Using these wheels with rim brakes may damage the rims and cause an accident that may result in serious injury or even death.
- Check that the axle release lever does not interfere with the disc brake rotor even when it is fully engaged. If the axle release lever is on the disc brake rotor side, it may interfere with the disc brake rotor, which is dangerous. If the axle release lever interferes with the disc brake rotor, stop using it immediately and contact your place of purchase or distributor.
- For details on the E-THRU axle, refer to the E-THRU axle user manual.
- Tires should be installed and removed by hand. If it is difficult, you can use a resin tire lever for tubeless wheels. In such cases, be sure to check the rim surface for dents, scratches, or cracks, as there is a risk of damaging the air seal between the tire and the rim, which may result in air leakage. For carbon rims, check for peeling or cracking of the carbon. Finally, make sure that there is no air leakage.
F12 (front 12mm axle), R12 (rear 12mm axle) wheel (hub axle)
- This wheel can only be used in combination with a special front fork/frame and hub axle. If used in combination with any other front fork/frame or hub axle, the wheel may come off the bicycle while riding, resulting in serious personal injury.

WARNING
- Please note that a taller rim is more susceptible to wind and causes unstable riding.
Warming-up time
- Disc brakes have a certain warm-up time, and braking power gradually increases as the warm-up time increases. Make sure you are aware of such increases. Otherwise, you may lose control of the bicycle, fall, and be seriously injured. The same situation occurs when replacing brake pads or disc brake rotors.

Manufacturer details
Shimano INC
3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan
Telephone number: +81-72-223-3210 / FAX:+81-72-223-3258
WEB: shimano.com
Email: contactshimano@shimano-eu.com

EU representative:
Shimano Europe BV
High Tech Campus 92, 5656 AG Eindhoven, the Netherlands
Tel: +31-40-2612222
WEB: shimano.com
Email: contactshimano@shimano-eu.com
EU contact: https://bike.shimano.com/information/distributors-list.html